Looking for:
Ge washer repair manual download |
Ge washer repair manual download
Appliances WSSR Technical Service Manual. Dimensions And Installation Information. Owner's Manual And Installation Instructions. Installation Information. Mini Manual Inflate. User Manual. Training Manual. GTW series. Energy Manual. Monogram WWAM. Monogram ZBD Profile G Profile GPDH Profile P Profile Washer. Profile WHSB Dimension Manual.
Profile WNSB Profile WPDH Profile WPGT Profile WPRB Installation Instructions. Spacemaker SH Spacemaker WCXH Spacemaker WPXH Spacemaker WSKS Product Information. Page 11 Dispenser Drawer Area: Detergent and fabric softener may build up in the dispenser drawer. Residue should be removed once or twice a month. Then reach back into the left rear corner of the drawer cavity and press down firmly on the lock tab, pulling out the drawer.
Page 13 Pull the drawer out to its stop position. Place the pedestal against the bottom of the washer or dryer. Ensure that the drawer front is Remove the screws from the drawer slides. Slide the drawer out of the base and set it aside. Page 14 Screw locknuts onto the supplied leveling legs. Ensure that the slides are closed, then slide the Turn the nuts toward the bottom and against drawer into the opening. Align the drawer supports to the slides on each Install the leveling legs, with locknuts, in each side.
Dryer models that currently qualify for inches stacked. Caution: Do not lay dryer on its back. Use the packing material or a protective surface when laying dryer on its side. Carefully lay the dryer on its side. Do not push on the dryer after it is stacked on the washer. Follow the fabric manufacturer's care label when selecting spin speed. Page 19 Cold: The available selection of spin speeds is controlled by cycle selection.
Use caution to avoid injury and the pump cleanout, pump, tub drain hose, heater assembly, inverter, wire junction box, front dampers, wear Kevlar gloves or equivalent protection.
Page Control Panel From inside the cabinet, lift and push forward to Control Panel release the bottom tab from the front bracket. The control panel is held in place with 5 Phillips- head screws and 5 tabs. To remove the control panel assembly: Remove the top panel.
Page 25 Control Board The control board is mounted in a housing that is attached to the inside of the control panel. The control board and housing are replaced as an assembly. The control board assembly is held in place by 4 Phillips- head screws and 3 tabs. See Control Panel The door lock contains a door switch and solenoid Pull the cycle knob off. A release ring, located at the bottom, allows for Remove the 4 Phillips-head screws that hold the manual unlocking of the door.
Page Door Strike Use a long-nose pliers to grasp the wire loop at Note: The door latch is solenoid activated. It can the spring location and expand it to clear the remain locked after power is removed. To manually unlock door: Disconnect the washer from electrical supply.
Page 30 Caution: A small retainer for the dispenser motor wiring, located underneath the unused inlet, is fragile. To avoid breakage, use minimal outward pressure when releasing wiring.
Inlet Hose Release the dispenser motor wiring from the retainer. Inlet Tube Remove the 2 Phillips-head screws that attach Tank Inlet the motor and clip to the dispenser tank. Page 31 Remove the 2 Phillips-head screws that hold the Remove the dispenser from the cabinet. Care must be taken to avoid damage to the dispenser tank. Remove the water inlet pipe by twisting and pulling outward. Page Water Level Control Water Level Control Operation Water Level Control When the machine is empty, the foam switch is The water level control is installed on the cabinet closed and the motor circuit is disabled.
When the right side top brace. See Top Panel occur at this water level. Page 36 To remove the pump: Disconnect the 2 wires from the pump. Remove the service panel. Outlet Caution: Under normal conditions, approximately Hose 1 quart of water will drain out when the pump Pump Wires cleanout is removed. Drain Hose Place a shallow pan under the drain cleanout. Turn the pump cleanout counterclockwise approximately 2 turns, then pull outward.
Page 38 To replace the thermistor: To reinstall the heater assembly: Push the thermistor into the rubber gasket until Slide the heater assembly into the tub opening fully seated.
Note: Ensure heater assembly is fully seated in the tub. Page 39 To remove the inverter: Inverter Remove the service panel. See Service Panel The inverter receives commands from the control board and controls motor operation. The inverter is Press the 4 tabs inward and remove the junction enclosed in a protective housing and is located on box cover. The motor assembly consists of a reversible, Remove the plastic wire tie that holds the motor variable speed, 3-phase induction DC motor, and wiring in place.
The motor drives the tub drive pulley with a 7-rib belt. Page 41 On the inverter board, check for an approximate Remove the belt by turning the tub drive pulley resistance value of 6 ohms between any two of and rolling the belt off the pulley.
Page Door Note: The threaded plate can fall out of the Door recessed slot in the motor mount. Ensure this plate is reinserted in the slot upon reassembly. The door should protect cover and ring.
No comments:
Post a Comment